Calculators
Calculation dashboard
Engineering calculation tools and your saved calculations.
44
Available calculators
9
Categories
0
Saved calculations
7
Report formats
Available calculators
Every calculator opens free, with no account. Click one to start.
Cable Sizing 15
- c0005 Cable Voltage Drop (AC3) Calculate voltage drop for three-phase cable runs per AS/NZS 3008.1.1.2017 standard
- c0006 Motor Cable Sizing Comprehensive motor cable sizing with four critical checks (CCC, VD, SC, EFL)
- c0015 Lighting Circuit Voltage Drop Calculate voltage drop in parallel-connected lighting circuits with sequential cable runs
- c0018 AC Light Circuit Voltage Drop Calculate voltage drop in parallel-connected single-phase AC lighting circuits with cumulative analysis
- c0019 DC Cable Sizing Calculator Calculate conductor size and voltage drop for DC cables in solar PV, battery, and DC distribution systems
- c0020 HV Cable Sizing Calculator Three-phase high voltage cable sizing with Nexans Olex data (3.3kV-33kV)
- c0027 NEC Cable Sizing Comprehensive NEC cable sizing with continuous load, ambient, bundling corrections, and voltage drop
- c0041 CEC 2024 Canadian Cable Sizing Balanced LV three-phase general-load and motor cable sizing to CSA C22.1:24
- c0030 Load Cable Sizing Comprehensive load cable sizing with four critical checks (CCC, VD, SC, EFL)
- c0042 Cable Size Range Range of standard cable sizes that conform for a given load and installation (CCC, VD, SC, EFL, overload coor…
- c0043 Cable Permissible Load Largest load and protective device a cable may carry for its installation (CCC, VD, SC, EFL, overload coordin…
- c0044 Motor Cable Selection Chart Max cable length and loading chart across motor ratings and cable sizes for one installation (AS/NZS 3008.1.1…
- c0031 Load Cable Sizing (1-Phase) Single-phase load cable sizing with four critical checks (CCC, VD, SC, EFL)
- c0032 Motor Cable Sizing (1-Phase) Single-phase motor cable sizing with four critical checks (CCC, VD, SC, EFL)
- c0035 Cable Volt Drop Table Maximum cable length matrix based on running voltage drop per AS3008
Power & Voltage 3
- c0001 Three-Phase V-I-P Calculator Calculate voltage, current, power, and impedance for 3-phase electrical systems
- c0002 Single-Phase V-I-P Calculator Calculate voltage, current, power, and impedance for single-phase electrical systems
- c0004 Power-Motor Calculator (AC3) Calculate electrical parameters for three-phase AC motors including current, apparent power, reactive power, …
Protection & Fault Analysis 8
- c0003 Earth Fault Loop Calculator Calculate earth fault loop impedance for electrical safety analysis and protection
- c0007 Arc Flash Hazard (IEEE 1584-2018) Calculate arcing current, incident energy, arc flash boundary, and PPE requirements
- c0009 Short-Circuit Current Three-phase short-circuit current calculations using Bussmann point-to-point method
- c0029 NEC Short Circuit Analysis Calculate fault currents and equipment interrupting ratings per NEC 110.9, 110.10, and 408.6
- c0033 CB Overload Protection Overload protection coordination per AS/NZS 3008.1 Clause 2.5.3
- c0034 Earth Fault Loop Impedance Calculate Zs including source impedance, cable impedance and standard checks
- c0038 Lightning Risk Assessment Lightning risk assessment per IEC 62305-2 for R1 (loss of human life)
- c0039 Protection Coordination TCC Time-Current Characteristic curve generation and coordination analysis
Motors & Drives 2
Equipment Sizing 5
- c0008 CT Selection & Sizing Current Transformer selection and sizing with burden, saturation, and ALF checks
- c0014 Generator Sizing Calculator Calculate required generator capacity based on connected loads, diversity factors, and motor starting require…
- c0016 MV Capacitor Bank Sizing Comprehensive MV capacitor bank sizing with power factor correction, harmonic analysis, reactor design, and e…
- c0021 UPS Selection & Battery Sizing Size UPS systems and battery banks for backup power with runtime calculations
- c0024 Transformer Sizing & Specification Comprehensive transformer sizing and specification per AS/NZS 60076
Load & Distribution 5
- c0022 Maximum Demand Calculator Calculate maximum demand for residential electrical installations per AS/NZS 3000:2018
- c0023 Commercial Panel Maximum Demand Calculate maximum demand for commercial/industrial panels per AS/NZS 3000 Table C2/C3
- c0025 Load Flow Analysis (Gauss-Seidel) Multi-bus power system load flow analysis using Gauss-Seidel iterative method
- c0028 NEC Distribution Panel Sizing Size three-phase distribution panels per NEC Article 220, 430, and 310 standards
- c0012 Switchroom Heat Load Calculate HVAC cooling requirements for switchrooms and control buildings
Earthing 2
Mechanical 3
- c0010 Positive Displacement Pump Calculator Calculate duty point and suction safety for reciprocating positive displacement pumps
- c0011 Centrifugal Pump System Calculate TDH, NPSH, and slurry settling for pump selection
- c0026 Belt Conveyor Design Complete mechanical design for belt conveyors: capacity, belt sizing, tensions, power, and drive selection
Recent calculations
Every calculator is free to use, no account needed
Sign in to save calculations and export PDF/Excel reports.